Flintec LDU 68.2 Manuale Utente

Flintec GmBemannsb74909 MeGERMANYwww.flinteTmbH bruch 9 ckesheim Y ec.comTypeFirmHardwareLoad Ce LDUTECHNmware Verse Version 6D

LDU 68.5.4. TLDU 68Pin no0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Remarks:  UA 73Valid  UA 775.5. LThe load cecells. The iThe sense chapte

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 11 of 286. Calibration and Calibration Sequence The calibration of LDU 68.x is only

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 12 of 287. Commands – Overview Command Short description Parameter value Page AD

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 13 of 288. Commands Description For better clarity, all commands are divided into gro

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 14 of 288.2. Calibration Commands – CE, CM, DS, DP, CZ, CG, ZT, ZI, FD, CS 8.2.1. C

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 15 of 288.2.6. CG Set Calibration Gain (Span) This is the reference point for calib

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 16 of 288.3. Motion Detection Commands – NR, NT The motion detection facility provid

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 17 of 288.4. Filter Setting Commands – FL, FF, UR A digital filter can be set which

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 18 of 288.5. Taring and Zeroing Commands – SZ, RZ, ST, RT The following commands all

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 19 of 288.6. Output Commands – GG, GN, GT, GS, GF, GW, GA The following commands “Ge

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 2 of 28Table of Contents: 1. Safety Instructions ...

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 20 of 288.7. Auto–transmit Commands – SG, SN, SF, SW, SA The following commands allow

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 21 of 288.8. Commands for External I/O Control – IN, IO, IM The LDU 68.1 has 2 indep

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 22 of 288.9. Setpoint Output Commands – Sn, Hn, An The LDU 68.1 has 2 logic outputs

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 23 of 288.10. Communication Setup Commands – AD, BR, CL, DX, TD, OP 8.10.1. AD Devi

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 24 of 288.11. Save Calibration and Setup Data Commands – CS, WP, SS, GI, PI The cal

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 25 of 288.12. Trigger Commands – SD, MT, GA, TE, TR, TL, SA Note: All changes to th

LDU 68.8.12.6. TLThis comm Master In the examtrigger comDefault sett Note: All trtrigger (Digsetting disa Figure: T 8.12.7. SA Master This comm.1

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 27 of 289. Use in “Approved” Applications (LDU 68.1 only) The term “approved” applie

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 28 of 2810. Updates – Firmware Download For a software update the LDU xx.x amplifier

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 3 of 288.7. Auto–transmit Commands – SG, SN, SF, SW, SA ...

LDU 68.RIGHTS AAll rights re No part of tmeans, meGmbH No patent lprecaution omissions. herein. The informinformed if the use of t FLINTEC r Neither

LDU 68.2. D 0 MonaHersteAnsch Produ Das bThis p RichtParlamzur AnMitglieVerträ89/33RichtDie AQualitQualitDiese den geZusich FolgenAs a pOIML DIN E

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 6 of 283. Introduction and Specifications The model LDU 68.x is a precise digital am

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 7 of 284. Communications and Getting started 4.1. Serial Interface Communicating wit

LDU 68.1 & 68.2 Technical Manual, Rev. 12 January 2010 Page 8 of 284.3. Baud Rate / Device Address Baud Rate: For baud rate setup use command B

LDU 68.5. H5.1. W 5.2. W 5.3. W .1 & 68.2 TechHardwarWiring With Unit With Unit hnical Manualre and WAdapterAdapter, Rev. 12 JanWiring r UA 77.1r